Getting a gas snow blower ready for winter

Ariens Deluxe 24 two-stage snow blower in orange, seen from the front left on a plain gray backdrop
Product image: Ariens. Manufacturer render on an AI-generated background.

Check the fuel, oil, tires and controls before the first snow. This guide uses the manuals for the Toro Power Max 826 OXE, model 37797, and Ariens Deluxe models 921069 and 921070. Their starter limits and skid settings differ. Match the model number before following a numerical setting, and use the engine manual where your machine refers you to it.

These are document-based instructions, not a report of using either machine. Allow extra time for servicing if you discover old fuel, damaged parts or controls that do not stop correctly.

Before you start

  • Have the correct operator and engine manuals, safety glasses, a tire gauge and a hand pump.
  • Use fresh fuel meeting your manual’s requirements. Both manuals specify at least 87 octane and no more than 10% ethanol.
  • Have the specified engine oil and tools for any adjustment you intend to make.
  • For electric start, use the grounded outdoor cord specified for your model. Replace a damaged cord.

Do maintenance on level ground with the engine off, key removed, moving parts stopped and hot parts cooled. Disconnect the spark plug wire before maintenance. Keep children and other people clear of the working area.

1. Deal with fuel left from storage

Check how the machine was stored. Toro’s manual describes treating the last fuel, running the tank dry and restarting until the engine will no longer start. Ariens describes stabilized fuel left in the tank with the fuel valve closed after running the carburetor dry. Those instructions are for the named models, not interchangeable storage routines.

Briggs & Stratton’s winter-preparation guidance recommends draining fuel left from the previous season. If you do not know what is in the tank, follow your model’s draining procedure or have a service shop handle it. Adding fresh gasoline does not establish that old fuel is usable.

  1. Move the machine outdoors and make sure the engine is cold.
  2. Place the approved fuel container on the ground, away from flames, sparks and smoking.
  3. Fill only to your manual’s limit. Toro specifies no higher than the bottom of the filler neck.
  4. Wipe up spills and secure the tank and container caps.

2. Check oil, tires and skid clearance

Check the oil using the engine’s specified dipstick procedure. Do not guess whether the dipstick should be screwed in for a reading. Ariens refers this check to the engine manual. Toro’s manual includes a pictorial procedure and lists both excessive and insufficient oil among possible starting problems.

For the Toro model covered here, tire pressure is 17 to 20 psi on both sides. Ariens directs owners to the tire sidewall figure and warns to use a hand pump, standing to one side. Set tire pressure before adjusting the skids.

On the named Ariens models, adjust the scraper blade before the skids. Its skid procedure uses 1/8-inch spacers for smooth surfaces and 7/8-inch spacers for uneven or gravel surfaces:

  1. Put the machine on a hard, flat surface.
  2. Place the specified spacers under both ends of the scraper.
  3. Loosen the skid hardware and lower the skids to the ground.
  4. Keep both sides even and tighten the hardware before removing the spacers.

Toro gives its own skid and scraper procedure and says to lower the skids for gravel. It does not specify Ariens’ gravel clearance. Do not transfer the 7/8-inch setting to a Toro simply because another manual supplies a number.

3. Start the engine outdoors

Reconnect the spark plug wire after completing the maintenance checks. Start and run the engine outdoors, never in a garage or other enclosed space. CPSC warns about fatal carbon monoxide exposure from snow thrower engines in enclosed areas. An open garage door is not a reason to run it inside.

For Toro model 37797, check the oil first, then:

  1. Open the fuel valve a quarter turn counterclockwise.
  2. Fully insert the ignition key.
  3. Press the primer three times, holding it for a second each time. Below -10°F, this manual specifies six presses.
  4. Move the choke to “Choke”.
  5. Move the throttle to “Fast”.
  6. Use the recoil handle or electric starter. As the engine warms and runs smoothly, move the choke gradually toward “Run”.

The Ariens sequence is choke on, key inserted, fuel valve on and throttle fast. Prime a cold engine three times, covering the primer’s vent hole and holding each press for one second. Do not prime a warm engine. Gradually move the choke off as the engine warms.

Toro model 37797 uses five-second on and off cycles, while Ariens 921069 and 921070 require at least one minute between attempts
Electric starter limits for Toro model 37797 and Ariens models 921069 and 921070, from their operator manuals.

For the Toro electric starter, alternate five seconds on with five seconds off, stopping after ten unsuccessful attempts and contacting an authorized dealer. For Ariens, each attempt must last no more than five seconds, with at least one minute between attempts.

Toro specifies a UL-listed 16-gauge outdoor cord no longer than 50 feet. Ariens specifies a grounded outdoor cord rated for at least 13 amps, UL listed or CSA certified. Connect it to the machine before the outlet. After starting, disconnect at the outlet first, then the machine, and leave it unplugged when not starting.

4. Check that the auger and drive stop

With nobody near the discharge or moving parts, test the controls from the operator’s position. On the Toro, squeeze the right-hand auger lever by itself, then release it. The auger should stop. If both levers are engaged, the traction lever holds the auger control engaged, so release both to stop them. Do not mistake that interlock for a failed control.

Ariens specifies that its attachment must stop within five seconds after release. Keep that limit with the Ariens test. Do not substitute it for a different model’s check.

Check the Toro traction drive in R1 and then forward position 1, releasing the traction lever before changing the selector. The machine should move in the selected direction and stop when released. If it creeps, goes the wrong way or the auger fails to stop, shut the engine down and have the fault corrected before using it.

If it won’t start

Check the key, fuel valve, throttle, choke, spark plug connection, fuel condition and oil level against the manual. Follow its starter rest periods instead of repeatedly cranking. Stop if you find leaking fuel, a damaged cord or another defect.

Ariens includes a frozen-impeller check with the key removed: engage the attachment clutch and try the recoil handle. If it will not pull, its procedure calls for thawing the machine in a warm area. Do not force a stuck starter or assume freezing is the only possible cause. Persistent starting trouble belongs with a service dealer.

After clearing snow

Follow the model’s shutdown and freeze-prevention routine. For a blocked chute, shut off the engine, remove the key and wait for all moving parts to stop and hot parts to cool. Use the clean-out tool, never your hand. Keep it with the machine so you can reach it when needed.

At the end of the season, follow the correct storage procedure again. Ariens also calls for removing salt and ice-melt residue with mild soap and low-pressure water.

Sources

Basis

Research-based: written from the published sources listed above, primary: The Toro Company, AriensCo. We have not used the products discussed ourselves, and any measurement quoted belongs to its source.

This guide was created with the help of AI. How we work

← Back to the blog